| description:
|
OBJECTID: System-generated unique identifier for each record within the feature classShape: System-generated geometry type of the featureGEODBID: Three-digit code that assigns editing responsibility to a community in the GIS Consortium FEATUREID: GIS-Consortium-generated unique identifier for each record within the feature class. All FEATUREIDs start with the GEODBID of the community that owns the record.DATECREATED: Date/time stamp from the moment the GIS record was created DATEMODIFIED: Date/time stamp from the last moment the GIS record was changed SOURCE: Organization that provided the data. The GIS Consortium standard is to preface the source with the three-letter municipal code of the community providing the data, followed by a dash. Example: VGV-Public WorksSOURCETYPE: Accuracy context for the recordAncillaryRole: Attribute that indicates whether the junction pushes (source) or pulls (sink) flow in a geometric network. Default setting for the GIS Consortium is none.Enabled: Boolean field to indicate whether water is allowed to flow through this feature ADMINISTRATIVEAREA: Owner of the area in which the feature is located INSTALLDATE: Date of installation for the real-world feature represented in the feature classLOCATIONDESCRIPTION: Statement illustrating the whereabouts of a featureOPERATIONALAREA: Retired field used to store a description for an operational area designated by a communityROTATION: Retired GIS tracking field used to turn the symbol that represents the feature on the map so that it matched how it would look in the real worldLIFECYCLESTATUS: Current state of the real-world feature SUBTYPE: Additional designation of the feature. Includes the following structures:bend: Fitting that connects two pipes where they change directioncap: Fitting that seals a pipe by screwing over the opening from the outsidecross: Fitting that connects four pipescoupling: Fitting that connects two pipesexpansion joint: Fitting with at least one airtight chamber that absorbs movement, stress, or vibrations where two pipes connectoffset: Fitting that brings one section of pipe out of one line and into a parallel linereducer: Fitting that joins two pipes of different sizesriser: Fitting with restrictors that allow water to move from a lower to a higher elevationsaddle: Fitting used to connect a smaller pipe to an existing larger pipe without separating the pipessleeve: Fitting retro-fitted around or inside an existing pipe. Used to extend the life of older or damaged sewers.tap: Fitting that connects a lateral to a maintee: Fitting used for connecting three pipes togetherweld: Fitting made of PVC that is connected to a PVC pipe with a solvent weldwye: Fitting that is Y shaped. Used to connect three pipes to create branch linesplug: Fitting that seals a pipe from the insideflared end section: Bell-shaped fitting attached to the end of a pipeWORKORDERID: Unique work order identifierELEVATION: Ground level height of real-world feature; measured in feet above sea levelWATERTYPE: Designation of water distribution or collection system to which the feature appliesJOINTTYPE: Type of connection between the structure and the pipeMATERIAL: Matter composition of the real-world feature DIAMETER1: Width of the real-world feature's connection to an adjacent pipe, represented in the feature class; measured in inches DIAMETER2: Width of the real-world feature's connection to an adjacent pipe, represented in the feature class; measured in inches DIAMETER3: Width of the real-world feature's connection to an adjacent pipe, represented in the feature class; measured in inches DIAMETER4: Width of the real-world feature's connection to an adjacent pipe, represented in the feature class; measured in inchesLEGACYTYPE: Retired GIS tracking code for the featureDEVICEID: Unique identifying code for the mechanical part, such as a serial number or model numberCOMMUNITYID: Unique identifying code selected by the communityOWNERSHIP: Organization with jurisdiction over the real-world feature represented in the feature classMAINTAINED: Organization responsible for the care of the real-world feature represented in the feature classDESCRIPTION: Statement illustrating the featureANGLE: The measurement of the angle between two diverging pipes; measured in degreesFID_WSJUNCTIONANNO_LINE: Unique identifier that can be joined to the FEATUREID field of the ssJunctionAnno_LINE feature class to provide a link between the feature and its label. CATEGORY: Retired field required for ArcGIS coverage modelsMECHANICAL: Retired field required for ArcGIS coverage modelsFID_WSUNDERGROUNDENCLOSURE_POLY: Unique identifier that can be joined to the FEATUREID field of the wsUndergroundEnclosure_POLY feature class to provide a link between the feature and the polygonMANUFACTURER: company/organization that produces the real-world featureGlobalID: System-generated unique identifier for each record that is required in replicated geodatabases REPLICAFILTER: Code used to filter data for the creation of custom geodatabases PRODUCTIONNOTES: Technical notes from GIS personnel WEBLINK: URL for a website related to the record DATEABANDONED: Date of abandonment for the real-world feature represented in the feature class |